When water runs down the brick or the crown crumbles, you need roof chimney repair in Pleasant Grove from a crew that climbs the roof instead of guessing from the driveway. We handle flashing failures, spalling brick, cracked crowns, and liner damage on homes across Utah County. Same-day estimates, no charge, and a written scope before we touch a shingle.
Roof chimney repair in Pleasant Grove means rebuilding the parts of a chimney that live above the roofline: the crown, the top courses of brick, the flashing, the cap, and the liner where it meets the flue. We pull the old crown sealant, grind out failed mortar with a masonry trowel and jointing tool, then rebuild with firebrick and refractory cement rated for the heat a wood-burning flue actually produces. Every job is checked against NFPA 211 and the IRC chimney code before we pack up.
Pleasant Grove sits in a freeze-thaw pocket along the Wasatch Front, and that cycle is brutal on masonry. Water soaks into brick, freezes overnight, and pops the face off. Add creosote buildup from a winter of burning and a flashing failure at the roof deck, and you have a leak that shows up as a brown ring on the ceiling in February. If you have been searching roof chimney repair Pleasant Grove UT near me and getting thin answers, that is exactly the job we run every week.
Every roof chimney repair in Pleasant Grove starts with a full inspection and ends with a hose test and a written summary. Here is what comes standard on the job, and what we quote separately when your chimney needs it.
We photograph the crown, flashing, cap, and brick from the roof, then check the attic deck for staining and rot. An inspection camera goes down the flue and a moisture meter checks the ceiling around the chase. You see every photo before we quote a repair.
We remove failed flashing, inspect the roof deck underneath, and install a new counter-flashing kit sealed against the brick. Step flashing, apron, and cap details all get done correctly, then we hose-test the whole assembly while you watch from the ground.
Cracked crowns get rebuilt with a proper slope and overhang so water sheds off the edge. Failed mortar joints get ground out and repointed with a masonry trowel and jointing tool, using refractory cement anywhere heat is a factor. Color-matched mortar keeps the repair invisible.
We inspect the cap for rust, loose fasteners, and animal entry, and repair or replace it if needed. The damper gets checked for full travel and a tight seal when closed. A stuck damper wastes heat all winter and lets cold air pour down the flue.
Once the mortar cures, we apply ChimneySaver waterproofing, a vapor-permeable sealant that blocks liquid water while letting the brick breathe. Then we run a smoke pen test on the flue and a hose test on the flashing before we pack up and walk the job with you.
You get a written summary of everything we found and fixed, along with photos of the finished work. Every repair carries a 1-year workmanship warranty. If something moves or leaks in that window, we come back and make it right at no charge.
We start on the roof and finish in the attic. A technician photographs the crown, flashing, cap, and brick from every angle, then checks the attic deck for staining and rot. We run an inspection camera down the flue and a moisture meter across the ceiling around the chase. This takes 45 to 60 minutes and tells us whether you need a repair or a rebuild.
You get a written scope the same day, itemized by task: crown rebuild, flashing replacement, tuckpointing, liner, cap. We tell you what is urgent, what can wait a season, and what we would skip if it were our own house. No pressure, no upsell on work the chimney does not need.
Before we cut anything, we lay tarps across the shingles and set fall protection. We remove the old cap and damper assembly, grind out failed mortar joints, and chip away any crown that has separated from the flue. Debris goes straight into buckets, not down the roof into your gutters.
We rebuild the crown with a proper slope and overhang, repoint joints with a masonry trowel and jointing tool, and set new flashing with a counter-flashing kit sealed against the brick. A stainless steel liner goes in where the old tile is cracked. ChimneySaver waterproofing goes on last, once the mortar has cured.
We run a smoke pen test on the flue, check the damper for full travel, and hose-test the flashing while you watch from the ground. Then we walk the roof line with you, show you the photos, and hand over a written summary. If anything moves in the first year, we come back at no charge.
Purpose-built equipment, used by trained technicians — so the job is done accurately the first time.
Goes down the flue to show cracked tiles, gaps in the liner, and creosote level. It is how we tell you whether a reline is needed or whether a sweep and repair will do.
Reads water content in the ceiling, framing, and brick around the chimney chase. It confirms whether a stain is an active leak or an old one, and it tells us when the structure has dried out.
Tests draft at the firebox and the flue. If smoke pulls up the flue, the chimney is drawing correctly. If it rolls into the room, we know the problem is draft, not just blockage.
Removes creosote and soot from the liner. We size the brush to the flue so it cleans the walls without damaging clay tile or a stainless liner.
Used for repointing mortar joints and rebuilding crowns. The jointing tool profiles the mortar to match the original brickwork so the repair blends in.
A complete counter-flashing system for sealing the chimney to the roof deck. Copper and stainless kits outlast the asphalt sealant that fails on most chimneys within a few years.
A vapor-permeable sealant applied to brick after mortar cures. It blocks liquid water while letting the brick breathe, which is the only way to waterproof masonry without trapping moisture inside.
A homeowner in Pleasant Grove West had a brown ring spreading across the ceiling every time it rained. Two contractors quoted a full chimney rebuild. The actual problem was flashing that had pulled away from the brick, letting water run straight down the chase.
We removed the failed flashing, checked the roof deck for rot, and installed a new Copperfield counter-flashing kit sealed against the brick. Hose-tested the assembly while the homeowner watched. The leak stopped that day, and the ceiling stain dried out within a week.
An Old Pleasant Grove home had a crown cracked clean through and mortar joints crumbling on the top six courses. Water was running into the flue every rain, rusting the damper and leaving a damp smell in the living room. The chimney had not been touched in 30 years.
We chipped out the failed crown, rebuilt it with a proper slope and overhang, ground out and repointed 40 feet of mortar joints with a color-matched mix, and sealed the brick with ChimneySaver. The damper was replaced. Total job took two days.
A windstorm took the chimney cap off a home near Mount Mahogany at 11 p.m., and rain was pouring down the flue into the firebox. The homeowner called our 24/7 line with water already pooling on the hearth.
A technician was on site by 1 a.m. to tarp the chase and stop the water. Two days later we installed a new stainless cap with a spark screen, checked the liner for water damage, and confirmed the damper still sealed. No ceiling damage, no liner replacement needed.
Most chimney calls start with one of a handful of symptoms. Here is what we see most often in Pleasant Grove, what happens if you leave it alone, and how we fix it.
Ask a pro →We trace the entry point with an inspection camera and moisture meter, then repair the flashing, crown, or brick joint where water is actually getting in. A hose test confirms the leak is dead before we leave. Most ceiling-stain calls in Pleasant Grove trace back to flashing failure.
We grind out failed mortar and repoint with a color-matched mix, replace spalled brick, and seal the surface with ChimneySaver waterproofing. Catching this early saves the chimney. Left two winters, the same damage usually means a full rebuild above the roofline.
We chip out the failed crown, rebuild it with a proper slope and overhang, and seal it against the flue. A correctly built crown sheds water off the edge instead of letting it pool against the brick. This is a one-day job and one of the highest-value repairs you can make.
We scope the flue, tell you whether a cast-in-place repair will work or whether you need a full stainless reline, and quote both. Insulated stainless liners from DuraVent and Selkirk meet NFPA 211 clearances and cut creosote buildup going forward.
Most roof chimney repairs in Pleasant Grove run $350 to $1,800 in 2026, depending on scope. A flashing reseal and cap replacement sits at the low end. A crown rebuild with tuckpointing and a new stainless liner pushes toward the top. Full chimney rebuilds above the roofline start around $2,800. We quote the whole job in writing before we start, so the number you hear is the number you pay.
A standard roof chimney fix Pleasant Grove job includes a roof and attic inspection, flashing repair or replacement, crown repair, mortar joint tuckpointing, cap and damper check, and a waterproofing sealant application once the mortar cures. If the liner is cracked, we add relining as a separate line item. You get photos of everything we found and everything we fixed.
Yes, and flashing failure is the number one cause of chimney leaks we see in Pleasant Grove. We remove the old flashing, inspect the roof deck for rot, and install a new Copperfield counter-flashing kit sealed against the brick with the correct step and apron details. Then we hose-test it while you watch. Most flashing leaks stop the same day.
A flashing repair or cap replacement takes 2 to 4 hours. A crown rebuild with tuckpointing runs a full day. A full rebuild above the roofline, including a new stainless liner, takes 2 to 3 days. We tell you the timeline before we start, and we do not leave a roof open overnight. If weather turns, we tarp and return the next clear day.
chimney repair near meIf you are searching chimney repair near me in Pleasant Grove, we cover the whole chimney, not just the roofline. Crown, brick, liner, cap, and damper work all come from the same crew, so you are not juggling three contractors for one leak.Explore →
chimney masonry repairSpalling brick and crumbling mortar joints are masonry problems, and they need a mason's hands. We grind out failed joints, match the mortar color, and repoint with a jointing tool so the repair blends into the original brick instead of standing out.Explore →chimney crown repairThe crown is the concrete cap on top of the chimney, and it takes the worst of Utah weather. When it cracks, water runs straight into the flue. We rebuild crowns with a proper slope and overhang so water sheds off the edge instead of pooling against the brick.Explore →
chimney reliningA cracked clay tile liner is a fire hazard and a carbon monoxide risk. We install insulated stainless steel liner systems sized to your appliance, meeting NFPA 211 clearances. Most relines finish in a single day and cut creosote buildup going forward.Explore →
chimney cap repairA missing or rusted cap lets rain, snow, and animals straight into the flue. We repair and replace caps with stainless or copper models sized to the flue, and we add spark screens where the fireplace needs them. It is one of the cheapest fixes with the biggest payoff.Explore →
chimney maintenanceAn annual inspection catches flashing failure, crown cracks, and creosote buildup before they turn into a leak or a fire risk. We recommend a check every fall before the burning season starts, and a sweep any time creosote reaches an eighth of an inch.Explore →
fireplace repairDamper malfunction, cracked firebrick, and smoke rolling into the room usually trace back to the chimney, not the firebox. We repair the damper, replace firebrick and refractory cement, and verify the flue is pulling correctly before we call the job done.Explore →
emergency chimney repairStorm damage, a fallen cap, or water pouring down a flue at 2 a.m. all qualify as emergencies. Our emergency roof chimney repair Pleasant Grove UT line runs 24/7, and we can tarp a damaged chase the same night to stop water until a full rebuild is scheduled.Explore →Water in the flue does not dry out on its own, and every freeze makes the crack wider. Call Blackstone Ridge at (855) 927-7517 for a same-day estimate on roof chimney repair in Pleasant Grove. Licensed, insured, and warrantied in writing. If it is urgent, we answer 24/7.
Get Free Estimate (855) 927-7517 →Call (855) 927-7517 any time, day or night, and a real person answers. For non-emergency work, we return messages within a few hours during business hours and can usually schedule an estimate the same week. Tell us what you are seeing and we will tell you what it likely means.