If you have been searching for chimney repair near me in Pleasant Grove, we handle the leaks, cracked crowns, spalling brick and failing liners that Utah County winters expose. Blackstone Ridge works on brick, metal and prefab chimneys across Pleasant Grove, UT. We inspect first, show you photos of what we find, and fix the actual problem instead of patching over it. Same-day and emergency calls are available.
Chimney repair near me in Pleasant Grove is the diagnosis and correction of structural, water and venting failures in a chimney system, from the firebox up through the flue, crown and cap. A real repair starts with an inspection camera run down the flue and a moisture meter reading on the brick. We check the damper, the flashing at the roof line, the crown sealant and the mortar joints. Then we fix what is actually failing, not just what is visible from the driveway.
Pleasant Grove sits in Utah County, where freeze-thaw cycles run from October into April and summer thunderstorms dump water fast. That combination cracks crowns, opens flashing seams and drives water into firebrick until it spalls. If you have been looking for chimney repair nearby Pleasant Grove after a storm, we see the same pattern over and over: a small crown crack that let water in for two winters before the liner showed damage. Catching it early is the difference between a $300 fix and a $4,000 rebuild.
Every repair call starts with a full inspection, because guessing is how money gets wasted. Here is what is covered in a standard visit, and what we quote separately when the job is bigger than a repair.
We inspect the flue with an inspection camera, check the firebox, damper, crown, cap, flashing and exterior masonry, and take moisture meter readings on the brick. You get a written summary and photos of anything that needs attention.
Cracked crowns get ground out and resealed with crown sealant. Loose or rusted caps get repaired or replaced with a stainless or copper cap sized to the flue, screened to keep animals out.
We pull failed flashing, rebuild the step and counter-flashing, and water-test the repair before we leave. Leaks that trace to masonry get waterproofing sealant applied to the exterior brick.
Failed mortar joints get cut out and repacked with fresh mortar using a masonry trowel and jointing tool. Spalled brick gets replaced with matching firebrick so the repair blends into the original chimney.
If the clay tile liner is cracked or missing, we show you the camera footage and quote a stainless steel liner sized to the flue. Relining is code-correct under NFPA 211 and IRC chimney code.
We protect the roof and landscaping, haul away debris, and walk you through the finished work. You get before-and-after photos and a workmanship warranty on the repair.
You call (855) 927-7517 and tell us what you are seeing: a stain on the ceiling, a drafty fireplace, crumbling mortar, or water in the firebox after a storm. We ask a few questions, give you a window, and confirm whether this is a routine visit or an emergency chimney repair near me Pleasant Grove UT situation. Most calls get a same-day or next-day slot.
We start at the roof and work down. An inspection camera goes up the flue, a moisture meter checks the brick, and a smoke pen confirms draft direction. We photograph the crown, flashing, cap, damper and every mortar joint. You get a plain-English rundown of what is failing and what it will take to fix it, usually within 45 minutes.
Before any tool comes off the truck, you get the scope and the price. No hourly guessing, no add-ons discovered halfway through. If the job is a simple cap replacement, we say so. If the liner is gone and relining is the right call, we show you the camera footage that proves it.
Crown cracks get ground out and resealed. Failed flashing gets pulled and rebuilt. Spalled brick gets replaced with matching firebrick and repointed. Liners get a stainless steel liner sized to the flue. Most repairs take two to six hours. Larger masonry rebuilds run one to three days, and we protect the roof and landscaping the whole time.
We run a draft test, check for leaks with a water spray at the flashing, and confirm the damper seals. Then we walk you through what we did, what to watch for, and when to schedule the next inspection. You get photos of the finished work and a workmanship warranty on the repair.
Purpose-built equipment, used by trained technicians — so the job is done accurately the first time.
Runs the full length of the flue to show liner cracks, gaps, creosote buildup and obstructions. You see the footage before we recommend any repair.
Reads water content in brick and mortar so we can tell whether a leak is active or old, and confirm the masonry is dry after repair.
Confirms draft direction and reveals backdrafting or leaks at the firebox and damper. It is the fastest way to diagnose a smoking fireplace.
Removes creosote and soot from the flue walls. Rotary sweeping reaches glazed creosote that a hand brush leaves behind.
Used for tuckpointing, crown repair and firebrick replacement. The jointing tool matches the original mortar profile so repairs blend in.
Stainless and copper caps plus replacement dampers ride on the truck so most repairs are finished the same visit.
ChimneySaver waterproofing and crown sealant protect the masonry from rain while letting the brick breathe, preventing spalling through winter.
A homeowner in Downtown Pleasant Grove had a spreading ceiling stain every time it rained. The crown had multiple hairline cracks, the flashing had pulled loose, and moisture meter readings on the brick were high.
We ground out and rebuilt the crown with fresh crown sealant, reset the step and counter-flashing, and applied ChimneySaver waterproofing to the exterior brick. Two storms later, the ceiling stayed dry and the stain stopped growing.
A home near Old Pleasant Grove had mortar falling onto the roof and four spalled bricks on the south face. The chimney was original to the house and the homeowner was told it needed a full rebuild.
We cut out the failed joints, repacked them with a matching mortar mix, replaced the four spalled bricks with matching firebrick, and sealed the crown. The chimney looked original again and passed inspection without a rebuild.
A family on Mount Mahogany had a prefab chimney with a cracked flue and a fireplace that smoked into the room. The inspection camera showed gaps in the liner and heavy creosote buildup.
We swept the flue with a rotary chimney sweep, installed a stainless steel liner sized to the appliance with Olympia Chimney components, insulated it to code, and replaced the warped damper. Draft tested clean and the fireplace stopped smoking.
Most chimney damage starts small and gets expensive fast. These are the calls we run most often in Pleasant Grove, and what happens if they get ignored.
Ask a pro →We find the entry point with a water test and moisture meter, then repair the crown, reset the flashing and apply waterproofing sealant. Most leak repairs are done in a single visit, and we water-test before we leave.
We grind out failed joints and repack them with fresh mortar, replace spalled brick with matching firebrick, and seal the crown. Tuckpointing now costs a fraction of rebuilding later.
We run an inspection camera to confirm liner condition, then install a stainless steel liner sized to the flue and insulated to code. Most relines are finished in one day.
We repair or replace the damper, confirm the seal and check the firebox for related damage. It is usually a same-day fix and one of the cheapest efficiency wins in the house.
Start by calling a local company that inspects before it quotes, like Blackstone Ridge at (855) 927-7517. Ask three things: are you licensed and insured in Utah, do you run an inspection camera, and do you provide photos of the problem. A company that answers all three is set up to do real repair work, not just sweep and leave. We serve all of Pleasant Grove and Utah County.
The best repair is the one that fixes the cause, not the symptom. For most Pleasant Grove homes that means sealing the crown, resetting flashing and repointing mortar before water gets into the flue. If the liner is already cracked, relining with a stainless steel liner is the durable answer. We inspect first, show you the evidence, and recommend only the work your chimney actually needs.
Yes. We take emergency calls around the clock for active leaks, storm damage, fallen caps and chimney fires. Call (855) 927-7517 and we will dispatch as soon as possible, usually within a few hours in the Pleasant Grove area. We stabilize the chimney first, then schedule the permanent repair, often the next business day.
Typical 2026 pricing in this area runs $180 to $450 for a cap, damper or crown seal repair, $600 to $1,800 for flashing and tuckpointing work, and $2,500 to $6,000 for a full stainless steel reline. Cost depends on chimney height, access, and how much masonry has failed. We quote the job in writing before we start.
chimney masonry repairWhen brick is spalling or mortar has crumbled out, masonry repair rebuilds the structure. We match the original brick profile and repoint with fresh mortar so the chimney looks and performs like it did when it was built.Explore →
chimney crown repairThe crown is the concrete cap on top of the chimney, and it is the first thing that cracks in Utah freeze-thaw cycles. We grind out failed crown sealant, rebuild the slope, and seal it so water sheds instead of soaking in.Explore →
chimney reliningA cracked or missing clay tile liner is a fire hazard. We install a stainless steel liner sized to your flue, insulated to code, and connected to the appliance collar. Most relines are finished in a single day.Explore →
chimney cap repairA loose or rusted cap lets rain straight into the flue and gives animals an open door. We repair or replace caps in stainless and copper, sized to the flue and screened to keep birds and squirrels out.Explore →
chimney maintenanceAn annual inspection catches crown cracks, flashing failures and creosote buildup before they turn into expensive repairs. We recommend one visit per year, ideally in early fall before the burning season starts.Explore →
fireplace repairDamper malfunction, cracked firebrick and worn mortar in the firebox all get fixed here. We rebuild fireboxes with refractory cement and firebrick rated for the heat, and we test the damper before we leave.Explore →
emergency chimney repairStorm damage, active leaks and post-chimney-fire calls get priority dispatch. We stabilize the chimney, tarp the roof if needed, and schedule the permanent repair, usually the next business day.Explore →
24/7 chimney repairOur phone line is staffed around the clock for chimney emergencies in Pleasant Grove and Utah County. If water is coming into your home through the chimney, call and we will get someone moving.Explore →One call gets you a real inspection, photo proof and a written price. We are licensed, insured and backed by a workmanship warranty on every repair. Call (855) 927-7517 and we will get you on the schedule, often the same day.
Book My Inspection (855) 927-7517 →Call (855) 927-7517 any time, day or night, and a real person answers. For non-emergency work, we return messages within a few hours during business hours and can usually schedule an estimate the same week. Tell us what you are seeing and we will tell you what it likely means.