Rusted outer jacket and seams
We clean and seal surface rust with ChimneySaver coating, or cut out and replace the rusted section with matching pipe. If rust has reached the liner, we install a new stainless steel liner inside the existing chase.
Rust, leaks, and liner damage fixed by local crews
Metal chimney repair in Pleasant Grove done right the first time
When your metal chimney rusts through, leaks at the flashing, or rattles in a Utah County windstorm, you need metal chimney repair in Pleasant Grove that holds. Blackstone Ridge handles metal chimney fix Pleasant Grove work for homeowners on Mount Mahogany, Battle Creek, and the State Street Corridor. We inspect, we quote, we fix it, and we test it before we leave your roof.
Careful work. Honest options.
About this service
What metal chimney repair in Pleasant Grove actually involves
Metal chimney repair in Pleasant Grove is the diagnosis and correction of damage to factory-built and stainless steel chimney systems, including rusted outer jackets, failed seams, cracked caps, and deteriorated liners. On a typical Pleasant Grove home, that means pulling the cap, running an inspection camera down the flue, checking every joint and storm collar, and testing the flashing with a moisture meter before we call it fixed. We replace what is failing and leave the rest alone.
Most of the metal chimneys we open up in Pleasant Grove fall into three buckets: rust from snowmelt and summer monsoon rain, liner deterioration from years of hot flue gas, and animal nesting that blocks the flue and traps creosote. A metal chimney fix Pleasant Grove homeowners call us for after the first cold snap is usually a damper malfunction or a cap that blew off in a Grove Creek canyon wind. We see it every season, and we know exactly what to look for.
- ✓ Stop water intrusion fast
- ✓ Restore safe draft
- ✓ Protect the roof deck
- ✓ Extend chimney life by years
What's included
What is included in our metal chimney repair
Every metal chimney repair in Pleasant Grove starts with a full inspection and ends with a draft test. Here is what is covered in a standard repair visit, and what we treat as a separate scope when the damage is more extensive.
✓
Full on-roof inspection
We climb the roof, pull the cap, and run an inspection camera down the full flue. We check the flashing, storm collar, crown, and every pipe joint. A moisture meter confirms whether water has already reached the chase.
✓
Camera-verified diagnosis
You see what we see. We show you the camera footage of the flue interior so you understand exactly what is failing and why. No guesswork, no vague explanations, no pressure to buy work you do not need.
✓
Component replacement
Failed caps, storm collars, damper assemblies, and rusted pipe sections get replaced with matching parts. We stock common sizes for Selkirk, DuraVent, and Olympia Chimney systems so most repairs finish the same visit.
✓
Sealing and waterproofing
We reseal the crown, reflash the roof penetration, and apply waterproofing sealant to the masonry and metal components. This is the step that stops the next leak before it starts.
✓
Draft test and close-out
We run a smoke pen to confirm proper draft, check the damper for smooth operation, and photograph the finished work. You get the photos plus a written summary of what was done and what to watch for.
✓
Workmanship warranty
Every repair we do carries a workmanship warranty. If something we fixed fails within the warranty period, call us and we come back. That is how we have built our Pleasant Grove customer base since 2023.
How it works
How our metal chimney repair process works
01
Phone triage
You call (855) 927-7517 and describe what you are seeing: water stains, rust flakes, a smell, a rattle. We ask the right questions, tell you what it likely is, and book a same-day or next-day visit. Most Pleasant Grove calls get a technician on site within 24 hours.
02
On-roof inspection
We climb the roof, remove the chimney cap, and run an inspection camera down the flue. We check the flashing, storm collar, crown, and every seam. A moisture meter confirms whether water is already inside the chase. This takes 30 to 45 minutes and you get a written scope before we touch anything.
03
Upfront quote
You get a flat price for the repair, not an hourly estimate. If we find something unexpected, we show you the camera footage and explain the options. You decide. No pressure, no surprise line items on the final invoice.
04
The repair itself
Depending on scope, we replace the cap, reseal the crown, swap a rusted section of pipe, install a new stainless steel liner, or reflash the roof. Most jobs take two to four hours. Larger relines run a full day. We protect the roof and clean up every screw and shaving before we leave.
05
Test and close-out
We run a smoke pen to confirm draft, check the damper for smooth operation, and photograph the finished work. You get those photos plus a written summary of what was done and what to watch for. If anything looks off in the next 12 months, call us and we come back.
Tools & methods
Tools and methods we use on metal chimney repair
Purpose-built equipment, used by trained technicians — so the job is done accurately the first time.
Inspection camera
Runs the full length of the flue to find liner cracks, creosote buildup, and animal nesting that a visual check from the roof would miss entirely.
Moisture meter
Confirms whether water has already reached the chase or roof deck, so we know if the leak is active or historical before we quote the repair.
Smoke pen
Tests draft after every repair. If the smoke does not pull cleanly up the flue, the job is not done.
Rotary chimney sweep and flue brush
Clears creosote and debris from the liner. We size the brush to your flue so we do not scratch the stainless surface.
Masonry trowel and jointing tool
Used on the masonry section of combination chimneys for tuckpointing and mortar repair that matches the original joint profile.
Chimney cap and damper assemblies
We stock caps and dampers for Selkirk, DuraVent, and Olympia Chimney systems so most replacements finish the same visit.
ChimneySaver and Rutland sealants
Crown sealant and waterproofing products rated for Utah freeze-thaw cycles. These hold up where cheaper sealants crack within a season.
Real results
Before and after.
Rusted storm collar stopped ceiling leak
Before
A homeowner on Mount Mahogany had a growing water stain on the ceiling below the chimney. The storm collar had rusted through and water was running down the pipe into the attic every time it rained or snow melted.
After
We replaced the storm collar, reflashed the roof penetration, and resealed the crown. The leak stopped immediately. Total job time was three hours, and the invoice came in at $340, exactly what we quoted.
New stainless liner restored safe draft
Before
A Downtown Pleasant Grove home had a metal chimney with a deteriorated liner and heavy creosote buildup. The fireplace smoked into the room every time it was lit, and the camera showed multiple cracks in the original liner.
After
We swept the flue, installed a new stainless steel liner sized to the appliance, and tested draft with a smoke pen. The fireplace now pulls cleanly, and the homeowner can burn without smoke backing into the living room.
Wind-damaged cap replaced same day
Before
A windstorm off Battle Creek tore the chimney cap off a home and bent the storm collar. The homeowner could see straight down the flue and was worried about rain and animals getting in before the next storm.
After
We dispatched the same day, installed a new stainless cap with mesh sized to the pipe, straightened the storm collar, and checked the flashing. The flue was sealed within 24 hours of the call.
Problems we solve
Metal chimney problems we fix for Pleasant Grove homeowners
Metal chimneys fail in predictable ways, and Pleasant Grove weather speeds up the process. These are the four problems we see most often, and what happens if they are left alone.
Ask a pro →↗
Failed flashing and storm collar
We remove the old flashing, inspect the roof deck for rot, and install new flashing sealed with high-grade waterproofing sealant. Most leak calls are resolved in two to four hours.
Cracked or missing chimney cap
We install a properly fitted cap with stainless mesh sized to your pipe diameter. We stock caps for Selkirk, DuraVent, and Olympia Chimney systems so most replacements happen the same visit.
Liner deterioration and creosote buildup
We sweep with a rotary chimney sweep and flue brush sized to your liner, then camera-inspect the full run. If the liner is compromised, we reline with a new stainless steel liner rated for your appliance.
Proof you can check
Licensed, certified, and reviewed
✓
CSIA Certified Chimney SweepChimney Safety Institute of America
✓
NFI CertifiedNational Fireplace Institute
✓
Utah contractor licenseUtah Division of Professional Licensing
✓
NFPA 211 compliant workNational Fire Protection Association
✓
Fully insured and bondedState of Utah
Most metal chimney repairs in Pleasant Grove run $180 to $450, with a cap replacement or flashing repair at the low end and a partial pipe section swap at the high end. Full stainless steel liner replacement runs $1,800 to $4,500 depending on chimney height and liner diameter. We quote a flat price after inspection, so you know the number before we start.
A standard metal chimney fix Pleasant Grove job includes a full on-roof inspection, camera scan of the flue, cap and storm collar check, flashing and crown inspection, and the actual repair. We reseal the crown, replace failed components, and test draft with a smoke pen before we leave. You get photos and a written summary of the work.
Yes. Surface rust on the outer jacket gets cleaned and sealed with a high-grade coating like ChimneySaver. Rust that has eaten through the metal means the section gets cut out and replaced with matching pipe. If rust has reached the liner, we install a new stainless steel liner inside the existing chase. We tell you which one you need after the camera inspection.
Most Pleasant Grove calls get a technician on site within 24 hours, and we run same-day metal chimney repair Pleasant Grove UT service for active leaks and storm damage. For emergency calls, we dispatch 24/7. Call (855) 927-7517 and we will give you a real arrival window, not a four-hour block.
More services
Related Services
chimney repair near meIf you searched chimney repair near me and landed here, you are in the right place. We handle metal and masonry chimneys across Pleasant Grove and Utah County, with same-day dispatch for most calls.Explore →
chimney masonry repairMetal chimneys often sit on a masonry base that needs tuckpointing or brick replacement. We handle both sides of the transition so the whole stack is sound, not just the metal section.Explore →
chimney crown repairA cracked crown lets water straight into the chase and rusts the metal flue from the top down. We reseal or rebuild crowns with crown sealant rated for Utah freeze-thaw cycles.Explore →
chimney reliningWhen a metal chimney liner fails, we install a new stainless steel liner sized to your appliance. This is the permanent fix for liner deterioration and the most common upgrade we sell in Pleasant Grove.Explore →
chimney cap repairA missing or bent cap lets rain, snow, and animals straight into the flue. We stock caps for Selkirk, DuraVent, and Olympia Chimney systems so most replacements happen the same visit.Explore →
chimney maintenanceAnnual maintenance catches rust, loose flashing, and creosote buildup before they turn into repairs. We recommend a yearly inspection for any metal chimney in Pleasant Grove, ideally in early fall before burn season.Explore →
fireplace repairFireplace and chimney work go together. If your damper sticks, your firebox has cracked firebrick, or your insert is not drafting, we fix it in the same visit as the chimney repair.Explore →
emergency chimney repairStorm damage, a cap that blew off, or an active leak into your ceiling is an emergency. We dispatch 24/7 for Pleasant Grove and surrounding Utah County neighborhoods.Explore → Ready when you are
Get your metal chimney repair in Pleasant Grove scheduled today
Call (855) 927-7517 and we will book a same-day or next-day visit. Flat pricing, camera-verified diagnostics, and a workmanship warranty on every metal chimney repair in Pleasant Grove we do. If it is leaking now, we run 24/7 emergency dispatch.
Book My Repair (855) 927-7517 →
Request an appointment
Get in touch with us
Call (855) 927-7517 any time, day or night, and a real person answers. For non-emergency work, we return messages within a few hours during business hours and can usually schedule an estimate the same week. Tell us what you are seeing and we will tell you what it likely means.
Call anytime(855) 927-7517Email the officeinfo@blackstoneridge.shop
Office hoursOpen 24 hours · 7 days a week